1 - Desmonte o filesystem
2 - Renomeie-o
3 - Monte o filesystem com novo nome

Para renomear utilize o comando chfs:

chfs -m [new filesystem name] [old filesystem name]

Referência:

Man page do comando chfs: http://publib.boulder.ibm.com/infocenter/pseries/v5r3/index.jsp?topic=/com.ibm.aix.cmds/doc/aixcmds1/chfs.htm

• Localização (PATH) dos comandos Veritas:

/etc/vx/bin

• Reconfigurar o Veritas:

# vxdctl enable

• Listar discos, volumes e status:

# vxdisk list
DEVICE       TYPE      DISK         GROUP        STATUS
EMC1_0       sliced    disk01  diskgroup    online
EMC1_1       sliced    disk02  diskgroup    online
c1t0d0s2     sliced    rootdisk     rootdg       online
c1t1d0s2     sliced    rootmirror   rootdg       online
c1t2d0s2     sliced    -            -            online
c1t3d0s2     sliced    -            -            online

• Criar um novo volume:

Ex: Criando um volume de 10 GB:

Se não especificar o diskgroup, por default, o volume será criado no rootdg

# vxassist make [volume name] 10240m

Especificando o diskgroup:

# vxassist -g [diskgroup] make [volume name] 10240m

• Listar informações detalhadas de um volume group:

# vxprint -g [diskgroup] -ht

• Criar filesystem no Solaris, caso não use o Veritas filesystem:

# newfs /dev/vx/rdsk/[diskgroup]/[volume name]

• Renomear um volume:

# vxedit -g [diskgroup] rename [old name] [new name]

• Remover um volume:

# vxassist -g [diskgroup] remove volume [volume name]

• Aumentar um filesystem (vxfs ou ufs)

Ex: Aumentando em 1 GB

# df -k /filesystem
Filesystem                         Kbytes        used    avail capacity  Mounted on
/dev/vx/dsk/[diskgroup name]/[volume name]    10321884   10166012 52654   100%    /filesystem

# /etc/vx/bin/vxresize -F [filesystem type] -g [disk group] [volume name] +1g

Referências:

1. 875-3053-10 - VERITAS Volume Manager, Command Line Interface, Administrator’s Guide: http://docs.filibeto.org/products-n-solutions/hardware/docs/pdf/875-3053-10.pdf
2. Basic VxVM Commands: http://eval.veritas.com/downloads/van/vm_quickref.pdf
3. vxresize man page: http://www.cuddletech.com/veritas/man/vxresize.m

Será criada uma imagem do VG, que pode ser restaurada caso necessário.

Antes de fazer o backup via savevg, defina os limites para unlimited, de modo a garantir que o backup seja criado mesmo que o tamanho exceda 2 GB:

ulimit -f unlimited (limite de tamanho de arquivo)
ulimit -d unlimited (limite de tamanho da área de dados)

Execute o comando savevg. Abaixo segue um exemplo com algumas opções:

/usr/bin/savevg  -f/path/nomedoarquivo -i -m -e -X nomedovg

-f: nome do arquivo

-i: cria o arquivo de dados chamando o comando mkvgdata

-m: adiciona as informações de mapa do VG

-e: exclui arquivos definidos no /etc/exclude.nomedovg

-X: expande automaticamente o /tmp caso necessário.

Exemplo:

$ /usr/bin/savevg  -f/mnt/foo-20080811.foovg -i -m -e -X foovg

Creating information file for volume group midwarevg..

Creating list of files to back up.
Backing up 27958 files……………..
27958 of 27958 files (100%)
0512-038 savevg: Backup Completed Successfully.
$

$ ls -l /mnt/fooserver-20080811.foovg
-rw-r—–   1 nobody   nobody   1246566400 Jun 18 14:10 /mnt/foos-20080811.foovg
$

Referência:

• “Commands reference: savevg command”: http://publib.boulder.ibm.com/infocenter/pseries/v5r3/index.jsp?topic=/com.ibm.aix.cmds/doc/aixcmds5/savevg.htm
• “Commands reference: ulimit command”: http://publib.boulder.ibm.com/infocenter/pseries/v5r3/index.jsp?topic=/com.ibm.aix.cmds/doc/aixcmds3/mkcd.htm

Caso um usuário trave sua conta, é preciso zerar o contador de logins além de destravá-lo para que ele possa logar novamente.

Para fazer isto, você pode usar o comando chsec conforme mostrado a seguir:

- Lista tentativas de login sem sucesso:

# lsuser -f [username] |grep unsuccessful_login_count
unsuccessful_login_count=8

- Listar se a conta está bloqueada:

# lsuser -f [username] |grep account_locked
account_locked=true

- Alterar para zero as tenativas falhas de login:

# chsec -f /etc/security/lastlog -s [username] -a unsuccessful_login_count=0

- Desbloquear o usuário:

# chsec -f /etc/security/lastlog -s [username] -a account_locked=false

- Lista novamente o número de tentativas mal sucessidas e se a conta está desbloqueada:

# lsuser -f [username] |grep unsuccessful_login_count
unsuccessful_login_count=0

# lsuser -f [username] |grep account_locked
account_locked=false

Agora o usuário estará apto a logar novamente. Caso ele não se recorde de sua senha então esta deverá ser trocada com o comando passwd.

Referência:

Comando lsuser: http://publib.boulder.ibm.com/infocenter/pseries/v5r3/index.jsp?topic=/com.ibm.aix.cmds/doc/aixcmds3/lsuser.htm

Comando chsec: http://publib.boulder.ibm.com/infocenter/systems/index.jsp?topic=/com.ibm.aix.cmds/doc/aixcmds1/chsec.htm

No exemplo abaixo quero avaliar se a data de um arquivo é 2006 e então exibir na tela a data e o nome do arquivo:

Saida do comando “ls -l”

-rw-r—–   1 userfoo   groupfoo  68578 Dec 29 2006  file_foo1.txt
-rw-r—–   1 userfoo   groupfoo  84609 Dec 29 2006  file_foo2.txt
-rw-r—–   1 userfoo   groupfoo  44587 Dec 29 2006  file_foo3.txt

Usando o awk:

# ls -l | awk  ‘{if ($8 == “2006″) print $8 “  ” $9}’

2006  file_foo1.txt
2006  file_foo2.txt
2006  file_foo3.txt

Mais informações sobre o uso do awk: http://www.grymoire.com/Unix/Awk.html

Veritas:

# vxdg -g bootdg free
DISK DEVICE TAG OFFSET LENGTH FLAGS
rootdg01 c0t0d0s2 c0t0d0 18837360 51408000 -

Aix:

# lsvg rootvg
VOLUME GROUP: rootvg VG IDENTIFIER: 00011824bd4eef54
VG STATE: active PP SIZE: 16 megabyte(s)
VG PERMISSION: read/write TOTAL PPs: 1084 (17344 megabytes)
MAX LVs: 256 FREE PPs: 376 (6016 megabytes)
LVs: 20 USED PPs: 708 (11328 megabytes)
OPEN LVs: 17 QUORUM: 2
TOTAL PVs: 2 VG DESCRIPTORS: 3
STALE PVs: 0 STALE PPs: 0
ACTIVE PVs: 2 AUTO ON: yes
MAX PPs per PV: 1016 MAX PVs: 32

Destacado em negrito no output de cada comando, a indicação do espaço livre.

Referência:

• VERITAS Volume Manager™ - Command Line Interface - Administrator’s Guide - Release 3.0.1: http://www.sun.com/products-n-solutions/hardware/docs/pdf/875-3053-10.pdf

• AIX Logical Volume Manager from A to Z: Troubleshooting and Commands: http://www.redbooks.ibm.com/abstract

• lsvg command: http://publib.boulder.ibm.com/infocenter/systems/index.jsp?topic=/com.ibm.aix.cmds/doc/aixcmds3/lsvg.htm&resultof=%22lsvg%22
  

O documento:

“Korn Shell Syntax - A Reference Guide”

http://www.context-switch.com/docs/kshrefltr.pdf

Ele ébásico, mas tem as condições de teste, e acaba sendo uma boa referência para consulta.

O site:

http://www.mtxia.com/css/Downloads/Scripts/Korn/index.shtml

Parameters:

mempools

Specifies the number of memory pools that the system real memory is split into.

Memory pools

The mempools value is used to subdivide the memory into pools. The parameter

mempools has a range from 1 (one) to, but not more than, the value of the

number of CPUs in the system. For example, if there are four CPUs in a system,

then the maximum value of mempools is 4 (four). Setting the value to 0 (zero),

restores the default number. In some circumstances, such as when most, but not

all, of the system memory is in use, better performance can be obtained by

setting this value to 1 (one).

Reference:

Aix 5L Performance Tools Handbook (SG24-6039-01)- Page 232

npskill

Specifies the number of free paging-space pages at which the operating system begins killing processes. If the npskill threshold is reached, a SIGKILL signal is sent to the youngest process. Processes that are handling SIGDANGER or processes that are using the early page-space allocation (paging space is allocated as soon as memory is requested) are exempt from being killed. The formula to determine the default value of npskill is as follows:

npskill = maximum (64, number_of_paging_space_pages/128)

The npskill value must be greater than zero and less than the total number of paging space pages on the system. It can be changed with the command vmo -o npskill=value.

Purpose:

Specifies the number of free paging-space pages at which the operating system begins killing processes.

Values:

• Default: MAX (64, number of paging space pages/128).
• Range: 0 to total number of paging space pages on the system .
• Type: Dynamic

Diagnosis:

N/A

Tuning

Increase the value if you experience processes being killed because of low paging space.

Refer To:

Values for the npswarn and npskill parameters

npsrpgmax

Purpose:

Specifies the number of free paging space blocks at which the Operating System stops freeing disk blocks on pagein of Deferred Page Space Allocation Policy pages.

Values:

• Default: MAX(1024, npswarn*2).
• Range: 0 to total number of paging space blocks in the system.

Diagnosis:

N/A

Tuning:

N/A

npsrpgmin

Purpose:

Specifies the number of free paging space blocks at which the Operating System starts freeing disk blocks on pagein of Deferred Page Space Allocation Policy pages.

Values:

• Default: MAX(768, npswarn+(npswarn/2)).
• Range: 0 to total number of paging space blocks in the system.

Diagnosis:

N/A

Tuning:

N/A

npsscrubmax

Purpose:

Specifies the number of free paging space blocks at which the Operating System stops Scrubbing in memory pages to free disk blocks from Deferred Page Space Allocation Policy pages.

Values:

• Default: MAX(1024, npsrpgmax).
• Range: 0 to total number of paging space blocks in the system.

Diagnosis:

N/A

Tuning:

N/A

npsscrubmin

Purpose:

Specifies the number of free paging space blocks at which the Operating System starts Scrubbing in memory pages to free disk blocks from Deferred Page Space Allocation Policy pages.

Values:

• Default: MAX(768, npsrpgmin).
• Range: 0 to total number of paging space blocks in the system.

Diagnosis:

N/A

Tuning:

N/A

npswarn

Specifies the number of free paging-space pages at which the operating system begins sending the SIGDANGER signal to processes. If the npswarn threshold is reached and a process is handling this signal, the process can choose to ignore it or do some other action such as exit or release memory using the disclaim() subroutine.

The value of npswarn must be greater than zero and less than the total number of paging-space pages on the system. It can be changed with the command vmo -o npswarn=value.

Purpose:

Specifies the number of free paging-space pages at which the operating system begins sending the SIGDANGER signal to processes.

Values:

• Default: MAX (512, 4*npskill)
• Range: 0 to total number of paging space pages on the system.
• Type: Dynamic

Diagnosis:

N/A

Tuning:

Increase the value if you experience processes being killed because of low paging space.

Refer To:

Values for the npswarn and npskill parameters

numpsblks

11-28-02, 01:40

prog_log :- It is used to find out if the dump was due to a hardware
problem.

vmker :- For finnding out free paging space. Nowadays this command is not
used as with time
the offset of free_paging_space/total_paging_space has changed.
The command od
vmker 16 used to be used to look at total paging space and free paging
space but
the field values have changed. It is easier to use the vmm
command to look at the vmker
data. The numpsblks field is the number of total paging space
blocks.
The psfreeblks is the free paging space blocks.

Fonte: http://www.dbforums.com/archive/index.php/t-579015.html

Parameter Description

http://download-uk.oracle.com/docs/html/A97297_01/appa_aix.htm

MINFREE The minimum free-list size. If the free-list space in the buffer falls below this size, the system uses page stealing to replenish the free list.

MAXFREE The maximum free-list size. If the free-list space in the buffer exceeds this size, the system stops using page stealing to replenish the free list.

MINPERM The minimum number of permanent buffer pages for file I/O.

MAXPERM The maximum number of permanent buffer pages for file I/O.

pinnable_frames:

Fonte: Redbook: SG24-7039-02 - Partitioning Implementations for IBMEserver p5 Servers, Pag 166.

Maxperm: maxperm influences paging behavior. Paging frees memory by copying the “least recently used” memory to disk for temporary storage. Tune maxperm to keep as much of the database in memory as possible when the system pages. The default setting is usually not optimum if the system pages as it favors paging out the database first.

The initial maxperm setting depends on whether the database filesystem resides on JFS or JFS2. For JFS, I automatically change the default “maxperm/maxclient” as above. For JFS2, I recommend using the defaults, and defer tuning to when the system is running a representative workload. The reason is that AIX classifies JFS and JFS2 memory differently. JFS is controlled by “maxperm”, which is a “soft” limit and more forgiving if set too low. JFS2, on the other hand, is controlled by “maxclient”, which is a “hard” limit. If set incorrectly, performance can be degraded. See “maxclient” section for JFS2.

When the system is under load, you can optimize the “maxperm” setting as follows. But first a little background. AIX classifies memory either as persistent or working storage. Persistent storage includes file cache, executables, and metadata. Working storage includes the database. Target amount of memory for persistent storage when the system is paging is the “maxperm” setting. (Note if the system is not paging, the maxperm setting is mostly ignored.) The default “maxperm” value of 80% favors paging out the database first, which degrades performance. In addition, the actual persistent memory requirements are typically much lower (20-50%).

The tuning methodology involves finding the actual persistent memory used when the system is under load (numperm). Then set “maxperm” to 5% below that value.

maxperm = numperm% - 5%.

(Note: be sure to set maxclient=maxperm. See “maxclient” below for more info.)

There are multiple commands for displaying memory usage. Here are two that I use.

AIX 5.1: “/usr/samples/kernel/vmtune | grep numperm”

AIX 5.2: “vmstat -v | grep numperm”

If you don’t have root access to run vmtune, you can use a different approach. Use vmstat “avm” column to estimate the size of the working storage. Calculate numperm% as follows

numperm% = 100% - “working storage%” = 100% - (avm *100 / total memory)

Note “avm” is in measured in 4k pages, so you’ll have to convert this number to the same units as total memory.

maxclient: A subgrouping of persistent memory. As such, “maxclient” is always less than or equal to “maxperm” (I set “maxclient=maxperm”).

The “maxclient” value sets the maximum amount of memory used by its members: JFS2, NFS, CDROM and Veritas file systems. The “maxclient” value is a “hard” limit, which is always enforced.

The importance is that JFS2 has a “hard” limit, while JFS does not. It’s better to leave the JFS2 as default until the system can be tuned while running a representative load. Setting “maxclient” too low can degrade JFS2 performance.

Tune the”maxclient” with the system under load. Use the “maxperm” tuning procedure for setting “maxclient”, and set “maxclient” equal to “maxperm”. If you want to be more precise, you can use the “svmon -G” command to view the amount of memory used by client storage. It’s shown under the “clnt” column (”in use”).

# svmon -G

size inuse free pin virtual

memory 131072 129422 1650 11704 50091

pg space 131072 4279

work pers clnt lpage

pin 11704 0 0 0

in use 47052 76146 6224 0

The svmon command also shows the working storage under the “work” column. It all comes together as follows:

Total memory = free+”working”+”persistent”

= free+work+(pers+clnt)

= 1650+47052+(76146+6224) = 1331072

Reference: http://users.ca.astound.net/baspence/AIXtip/AIX5_Initial_Tuning.htm

Eu gosto de usar a linha de comando. A partir da shell do Unix pode-se executar o comando:

dsmc restore ‘[arquivo a ser restaurado]‘ ‘[destino do arquivo]‘ <opções>

Ex:

dsmc restore ‘/home/usuario/teste.txt’ ‘/tmp/’ -subdir=yes -pick -inactive

O exemplo acima vai restaurar o arquivo /home/usuario/teste.txt no /tmp. As opções utilizadas acima não são obrigatórias:

-subdir: Com subdir igual a yes, no caso de restaurar um diretório, ele irá restaurar toda estrutura de subdiretórios abaixo dele. Muito útil para restore de diretórios.

-inactive: Vai listar as versões não ativas do backup que ainda não expiraram.

-pick: Esta opção vai listar os arquivos ao invés de já efetuar o restore. É muito útil para primeiro visualizar o arquivo e então selecioná-lo para o restore.

É possível também, ao invés de usar o “dsmc restore” direto na shell do Unix, chamar a linha de comando do TSM com o comando “dsmc” e então, usar a opção restore ou outros comandos do TSM:

# dsmc

tsm> restore ‘/home/arquivo.xxx’ ‘/tmp/’ -subdir=yes -pick -inactive

Mais informações no Manual da IBM de TSM para Unix, “Backup-Archive Clients Installation and User’s Guide”:

http://publib.boulder.ibm.com/infocenter/tivihelp/v1r1/topic/com.ibm.itsmc.doc_5.3.3/ans50000.pdf

Achei um resumo útil e decidi salvar aqui no “meu” bloco de notas.

Fonte: http://www.linuxquestions.org/questions/aix-43/aix-default-user-list-612651/

“I work at a company that gets audited all the time. The ones we’re most commonly asked to remove are guest, lpd, uucp, nuucp (if it’s there) and imnadmin. Here’s a list of accounts I put together about a year ago; most of it is relevant, I think:

daemon - The daemon user account exists only to own and run system server processes and their associated files. This account guarantees that such processes run with the appropriate file access permissions.

bin - The bin user account typically owns the executable files for most user commands. This account’s primary purpose is to help distribute the ownership of important system directories and files so that everything is not owned solely by the root and sys user accounts.

sys - The sys user owns the default mounting point for the Distributed File Service (DFS) cache, which must exist before you can install or configure DFS on a client.

adm - The adm user account owns the following basic system functions:
* Diagnostics, the tools for which are stored in the /usr/sbin/perf/diag_tool directory.
* Accounting, the tools for which are stored in the following directories:
o /usr/sbin/acct
o /usr/lib/acct
o /var/adm
o /var/adm/acct/fiscal
o /var/adm/acct/nite
o /var/adm/acct/sum

uucp - Owner of hidden files used by uucp protocol. The uucp user account is used for the UNIX-to-UNIX Copy Program, which is a group of commands, programs, and files, present on most AIX systems, that allows the user to communicate with another AIX system over a dedicated line or a telephone line.

guest - Allows access to users who do not have access to accounts.

nobody - The nobody user account is used by the Network File System (NFS) to enable remote printing. This account exists so that a program can permit temporary root access to root users

lpd - Owner of files used by printing subsystem. This account has been disabled.

imnadm - IMN search engine used for Documentation Library Search.

lp - Possibly something to do with printing.

invscout - Surveys the host system for currently installed microcode or Vital Product Data (VPD).

snapp - The account that manages Snapp, an extensible, XML-based application that provides a menu-driven interface for UNIX system administration tasks on a handheld PDA.

sshd - The user account for managing the sshd service.”